  Email: boe@boeep.com
Sludge Dryer
You are here: Home » Knowledge » Sludge Dryer

Sludge Dryer

Grit removal are commonly used to separate grain sediment substances that have large specific gravity and are macroscopic from sewage. Widely used as discharge equipment after grate and has pretreatment function in city sewage treatment plants, the guaranteed effectively follow-up work on the rails.
Also they can be used to separate grain substances from steelworks muddy water, sand-washing water and coal-washing water.
The low-temperature sludge drying equipment developed by BOE environmental Protection can directly dry sewage or sludge with a moisture content of less than 83% to dry sludge with a moisture content of 10%-30%. 
 
The reduction can be as high as 90%, and the effective sterilization can be as high as 90%.
Low energy consumption, no pollution, widely used in municipal sludge and industrial sludge (printing and dyeing, papermaking, electroplating, chemical industry, leather, pharmacy, etc.) for drying reduction. 
 
Dry sludge with 10%-30% moisture content can be gasified later , Mixed burning, composting, or building materials and other harmless resource disposal.
  • The low-temperature sludge drying equipment independently developed by BOE Environmental Protection uses the principle of low-temperature heat pump dehumidification and uses convection hot air drying to reduce the amount of wet sludge on the mesh belt. The whole set is the same as a fully enclosed type. Design, dry hot air without heat loss.
  • The refrigeration system is used to cool and dehumidify the humid air from the drying room, and at the same time recover the latent heat of moisture condensation to reheat the dry air. It is a combination of dehumidification (dehumidification and drying) and heat pump (energy recovery), and is the recycling of energy in the drying process.
    004
  •  
    Four-effect technology, twice the industry standard
    Four-effect condensation dehumidification drying technology is an advanced sludge drying reduction technology. It has significant advantages such as lower air outlet temperature, better drying capacity and efficiency, and more economical operating costs; adopts "four-effect condensation dehumidification and drying" equipment, and the comprehensive dehumidification performance ratio (SMER) is as high as 4kg.H2O/kw.h or more , The moisture content of dry mud is reduced to 10%-30%, which is more than 50% energy-saving than traditional low-temperature drying, which is twice the industry standard.

    A variety of molding technologies, comprehensive energy efficiency leading 40%.
    Based on years of successful experience, different types of wet mud, and different moisture content, different molding technologies are used to reduce the drying time of wet mud, and the comprehensive energy efficiency is 40% ahead of the industry.
  •  
    1.It can be widely used in the drying treatment of various types of sludge in municipal administration, printing and dyeing, papermaking, electroplating, chemical industry, leather, etc.;
     
    2.The daily dehumidification and water removal capacity of a single device ranges from 200 kg to 50 tons, and all models can meet;
     
    3.Electric energy can be used directly, or energy such as steam and waste heat can be used;
     
    4.It can be “centralized treatment” or “decentralized treatment” to meet the requirements of sludge disposal policies in different regions;
     
    5. It is not affected by the external environment temperature (low temperature in winter) and humidity (humidity in summer), suitable for use in various regions;
  •  
    1. Fully-enclosed low-temperature operation at 40-75℃, no nitrogen filling operation required;
     
    2. During the drying process, the oxygen content is less than 12%, the dust concentration is less than 60g/m3, the particle temperature is less than 70℃, and there is no danger of dust and explosion;
     
    3. The sludge is statically spread, and there is no mechanical electrostatic friction with the contact surface;
     
    4. There is no "sticky phase" stage of the urban sludge drying process (about 60%);
     
    5. The dry material is in granular form and there is no danger of dust;
     
    6. The discharging temperature is low (<50℃), no cooling is needed, and it is stored.
  •  
    1. It can directly dry the sludge with a moisture content of 83% to 10% without disposing in stages;
     
    2. There is no loss of organic components in the drying process, and the dry material has a high calorific value, which is suitable for later resource utilization;
     
    3. The reduction can be as high as 80%, which can save a lot of later transportation costs; 
     
    4. Using Pasteur (pasteurization) sterilization method-low temperature heat sterilization, the drying temperature is above 70 ℃ for 90 minutes to 120 minutes, and the effective sterilization is as high as 90%;
  •  
    1. Adopt heat pump heat recovery technology, closed drying mode without any waste heat emission;
    2. 80% wet mud is dried to 60% per ton, and the comprehensive power consumption is 125kw.h;
    3. 80% wet mud is dried to 10% per ton, and the comprehensive power consumption is 200kw.h;
    4. 4 kg of water can be removed per 1 kilowatt-hour of electricity (the dehumidification performance ratio is 1:4kg.H2o/kw.h);
  •  
    1. The entire equipment system adopts a closed design, no odor overflows, and no complicated deodorizing device is required;
    2. Using low temperature drying process, the amount of H2S and NH3 precipitation is greatly reduced;
    3. Condensate (sludge moisture) is easy to dispose of and can be discharged directly;
    4. Adapt to sewage plants in urban areas, villages and scenic spots;
  •  
    1. It occupies a small area, with an average treatment area of about 4m2 per ton of wet mud;
    2. It can be installed in the basement to save land area;
    3. No complicated civil structures and infrastructure, saving civil construction costs;
    4. The equipment is simple to install, and the installation and debugging cycle is short, saving time and cost;
  •  
    1. The equipment runs fully automatically, saving a lot of labor costs;
    2. "PLC+touch screen" intelligent control can realize remote centralized control;
    3. The moisture content of the discharge material can be adjusted arbitrarily (10%-50%);
  •  
    1. The use of corrosion-resistant materials such as stainless steel, and the heat exchanger with electroplating anti-corrosion treatment, have a long service life;
    2. There is no mechanical wear during operation, and the service life is more than 15 years;
    3. No vulnerable and consumable parts, easy to use and manage;

Nalco industrial services (nanjing) co., LTD

Type: chemical sludge
Dehydration form: screw dewatering
Moisture content of wet sludge: 85%
Moisture content of dry mud: 30%
Wet sludge volume: 2.7 tons / day
Product model: BOE2400FL
Energy consumption: 230 kw /t

 Everbright Wate Haimen project

Type: Municipal Sludge
Dehydration form: screw dewatering
Moisture content of wet sludge: 80%
Moisture content of dry mud: 50%
Wet sludge volume: 4.8 tons / day
Product model: Boe7200FL
Energy consumption: 250 kw /t

Zhejiang Runhong Environmental Technology Co., Ltd. 

Type: Electroplating Sludge
Dehydration form: plate and frame dehydration
Moisture content of wet material: 65%
Moisture content of dry mud: 20%
Wet mud volume: 500 tons / day
Product model: boe50000YR
Energy consumption: the comprehensive energy consumption is 120CNY / t

Hebei baosteel Can-making project

Type: chemical sludge
Dehydration form: screw dewatering
Moisture content of wet material: 83%
Moisture content of dry mud: 15-25%
Wet mud volume: 144 kg / day
Product model: BOE1200SL
Energy consumption: 330 kw /day

Hunan new combined biological pharmaceutical co., LTD

Type: Pharmaceutical sludge
Dehydration form: Multi-Disc screw dewatering
Moisture content of wet material: 80-85%
Moisture content of dry mud: about 20%
Wet mud volume: 7-8 tons/ day
Product model: BOE2400FL, BOE4800FL
Energy consumption: 230 kw/t

Hunan longteng biotechnology co., LTD

Type: Pharmaceutical sludge
Dehydration form: screw dewatering
Moisture content of wet material: 83%
Moisture content of dry mud: 30%
Wet mud volume: 3 tons per day
Product model: BOE2400FL
Energy consumption: 230 kw/ t

Wuxi biya auto parts co., LTD

Type: Electroplating Sludge
Dehydration form: plate and frame filter press
Moisture content of wet material: 75-80%
Moisture content of dry mud: 15-20%
Wet mud volume: 20 tons per month
Product model: BOE800XS
Energy consumption: 400-500 kw/ t

Pinghu satellite petrochemical project

Type: chemical sludge
Dehydration form: screw dewatering
Moisture content of wet material: 82%
Moisture content of dry mud: 10%
Wet mud volume: 65 tons / day
Product model: BOE800XS
Energy consumption: 1.2 tons steam / 1 ton water, electricity 40 CNY/ ton wet mud, comprehensive energy consumption 120 CNY /t

Sludge Dryer

BOEEP has over 20 years’ professional experience as a waste water treatment equipment manufacturer and engineering service enterprise.

PRODUCTS

QUICK LINK

CONTACT US

Add:NO.10 Zhenye Road, Yangmiao, Hanjiang, Yangzhou, Jiangsu, China
Tel:+86-514-87848766
Fax:+86-514-87894600
E-mail :boe@boeep.com
Hand phone: +86-18252568555
QQ: 31609749
Skype/Wechat/Whatsapp:+86-18252568555
Copyright ©️ 2018 Jiangsu BOE Environmental Protection Technology CO., Ltd.  Designed by Leadong  / Site Map